Technology of Placing gypsum tiles along with your own hands

Gypsum tiles have to be laid correctly, as not just the aesthetic look of decorative facing, but in addition the service quality

of this substance will rely on the technologies of job. The product is also universal, and it can be attached to plaster,

concrete, brick or gypsum board sheets, provided the top layer of the foundation is and has no defects.

If the defects of the foundation are important, it ought to be completely treated with primer, then a cement mortar is created,

which fills all the cracks. Subsequently the surface should be primed and dried. Primer treatment is essential to improve the bond

between the tile and the walls. In this case, its composition should choose a particular, containing components which stop the

look of fungus and mold.

In the modern interior of the rooms most often used gypsum tiles, even imitating natural stone or brick. To execute cosmetic

finishing your self, it’s essential first of all to select a scheme of tile placement and prepare a remedy. It is necessary to pay

attention to the reverse side of the material. If its surface includes an embossed surface masterfasada.ru, then the glue should be placed using

an trowel, also if it’s even, then using a notched one.

The technology of the job is as follows:

* A thin layer of glue mortar is put on the pre-prepared wall. It is spread over the base so that it is likely to put 4-5 tiles.

Decorative cladding may be put either on plasterboard, and on putty.

* Cover the rear side of the tiles with glue.

* Plaster elements are pressed against the walls and their location is adjusted. To align with the seams, it’s recommended to

use spacers.

* Finishing is carried out in rows, all which should be shifted by half of a tile. Facing is carried out into the corners of the

room, then immediately remove any residual mortar at the joints.

Drying the walls takes no more than a day and takes a continuous humidity and temperature within the room. The final stage in the

laying of gypsum tiles is the decoration. To do this, the joints between the components are filled with a special solution, the

shade of which matches the brick.

Decorative imitation of brickwork on the walls is completed in the following ways:

* Cutting the darkened surface of the seams of masonry with a bolt cutter with your own hands;

* laying of tiles under the brick:

* mimicking the format and colour of the side of one brick;

* Imitating a fragment of brickwork of several bricks.

The perfect way to decorate”under the brick” is the one which allows you to create a practical coating with the maximum look of

its similarity to natural masonry. All 3 ways to carry out this kind of finishing functions fulfill the demands, however, the

cutting edge of joints using a bolt will be labor-intensive and the creation of considerable amounts of dust, so let’s consider

more prevalent ways.

The old finish is removed from the walls, and also the surface, if necessary, is leveled to get rid of the requirement to paste

plaster on a thick layer of adhesive.

Combining these cladding with other types of interior finishes could be both systematic and performed without any apparent

consistency, chaotically, with fake of signs of aging.

With the support of decorative gypsum tiles it is possible to imitate a large number of textures.

A large number of textures may be imitated with the support of decorative gypsum tiles.

The wall on which it is to be installed must possess the following attributes:

* Hardness and strength of the surface;

* The absence of irregular areas and sharp sections;

* no more deformations.

Decorative tiles in the interior of this kitchen

Walls are created from a number of materials, let us break down the principles of setup.

When working with concrete, there will not be any big problems. It is just required to take into consideration the porosity of the

material. Concrete, that has practically no pronounced pores, ought to be treated with a great primer.

Mounting gypsum tiles concrete

Before beginning work on the setup of gypsum tiles to the walls, then it is well worth checking the strength of their surface.

After the plaster doesn’t drop off the wall and in the identical time holds well, you can simply paint it using primer.

Mount the tiles onto the painted concrete should not. The surface ought to be scratched, ensuring to misfire, then it needs to be

grouted and covered with a layer of plaster.